3-Phase Motor With Timer Wiring

3 Phase Motor with timer wiring:

This diagram shows how to make a 3-Phase Motor With Timer Wiring. In this circuit, we use a TP MCB ( Tripple Pole Minature Circuit Breaker ), four magnetic contactors, 3 phase motors, a DP MCB ( Double Pole Minature Circuit Breaker ), a timer, NC Switch, and a NO Switch. Here we need to connect all components like our diagram.

Diagram of 3 Phase motor wiring:

Fig 1: 3-Phase Motor With Timer Wiring

Components Need for this Project:

You can get the components from any of the sites below:

FT MCB [See Buy Click Amazon]
DP MCB [See Buy Click Amazon]
Timer [See Buy Click Amazon]
Motor Starter Protector [See Buy Click Amazon]
Contactor [See Buy Click Amazon]
NC Switch [See Buy Click Amazon]
NO Switch [See Buy Click Amazon]
3 Phase Motor [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the 3 Phase Motor wiring:

01. FT MCB

Fig 2: FT MCB

Four pole MCCB for Four wires connections, the one additional Four pole for neutral wire connection so that between neutral and any of the other three will supply. It is used where is the possibility of a high neutral current (due to unbalanced loads and /or Third and multiple Third harmonics current etc) and Neutral / Earth Protection is provided on Neutral. Four Pole Circuit Breakers Have advantages in the case When one of the Poles of the Device will get Damaged, and they also provide Isolation from neutral voltage.

02. DP MCB

Fig 3: DP MCB

Double pole MCB can control two wires. This circuit breaker is generally used in single-phase electric lines. Double pole MCB circuit breaker input has two wires supply two wires and an output. In a single-phase line, A double-pole MCB circuit breaker is used to give good production. This circuit breaker is provided through phase and neutral circuit breaker, it is very safe. This circuit breaker is preferred for home appliances. A DP MCB usually trips for 2 reasons 1. Overload 2. Short circuit.

03. Timer

Fig 4: Timer

Timer is a specialized type of clock used for measuring specific time intervals.An electromechanical cam timer uses a small synchronous AC motor turning a cam against a comb of switch contacts. This type of timer often has a friction clutch between the gear train and the cam, the cam can be turned to reset the time.A simple example of the first type is an hourglass. Working method timers have two main groups: hardware and software timers.Most timers give an indication that the time interval that had been set has expired.

04. Motor Starter Protector

Fig 5: Motor Starter Protector

3-phase Motor starters, motor protection circuit breakers (MPCBs) or manual motor protectors (MMPs) control wiring useing switching. There are electromechanical protection devices for the main circuit diagram. They are mainly used to switch motors ON/OFF manually and to provide fuseless protection against short-circuit overload and phase failures switching motor control circuit diagram.

05. Contactor

Fig 6: Contactor

A magnetic contactor is an electrical device used for load control, automation, and protection. It is much like a magnetic reel. However, relays are generally used for low power and voltage, on the other hand, when we think of high power, these heavy-duty contractors only come to mind. It basically works by switching the load on and off. It has 3 terminals whose inputs are denoted as L1, L2, L3, and outputs as T1, T2, and T3. The circuit of the load is made in automation mode or protection using auxiliary contacts. It has two types of terminals. 1) Normally Open (NO). 2) Normally Closed (NC)

06. NC Switch

Fig 7: NC Switch

Indicates the contacts of switches or automatic actionable devices. Simply put, the push switches, magnetic contactors, and relays that we use in the factory Normally have Close Contact exists. At this moment the switch will be in normally closed condition. Because already he is sitting close. When turned off the contact will open. To make ladder logic you need to understand NC contact. As already explained. The switch contact is already closed in NC. That is enough to understand.

07. NO Switch

Fig 8: NO Switch

The operator switch has its contact in Normally Open condition. To make Ladder Logic you need to understand NO contact. A Classic Switch has one Input And one Output. In "No Switch," YoungBoy Raps About Ammunition, Murder, Firearms, and Firearm Attachments Such as a Switch. The contact of the switch whose contact is already open is NO. That is enough to understand. no switch in a circuit, then the circuit will not function as intended. to write a program such that when the red light is on, This switch is now in normally open condition. When you push the switch it will close and the red light will turn on.

08. 3 Phase Motor

Fig 9: 3 Phase Motor

A Three-Phase Motor is an Electric Motor That Typically Receives its Power From a Three-Phase System (three-phase current) This can be realized via a Three-Phase Mains Supply or a Frequency Inverter. Three-Phase Motors are Available as Synchronous and Asynchronous Motors. Three Phase Alternating Current Power Motor is Economical to Supply Power to the data Center Since it Requires Less Conductor Material to Supply Electricity. This Explains Why 3 Phase Alternating Current Motor is Used in Electric Transmission, Generation, and Distribution in Most Countries Worldwide.

Thank You for visiting the website. Keep visiting for more Updates.

3-Phase Motor With Timer Wiring