Timer and contactor wiring diagram

Timer and contactor diagram:

This diagram shows how to make a timer and contactor wiring diagram. In this circuit, we use a start switch, a stop switch, a timer, a magnetic contactor, an indicator light, and a DP MCB ( Double Pole Minature Circuit Breaker ). First we need to connect  the DP MCB with the power source then connect the contactor timer ans star stop switch with the contactor. Lastly we need to connect the indicator with the powe source. 

Diagram of Timer & contactor wiring:

Fig 1: Timer and contactor wiring diagram

Components Need for this Project:

You can get the components from any of the sites below:

1. DP MCB [See Buy Click Amazon]
2. Contactor [See Buy Click Amazon]
3. Timer  [See Buy Click Amazon]
4. Start Switch  [See Buy Click Amazon]
5. Stop Switch  [See Buy Click Amazon]
6. Indicator Light [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

• single phase motor starter connection

• Motor Start with ON Delay Wiring

• Motor Start & Stop Wiring Diagram

• Motion sensor connection diagram

• Modular Contactor With Motor Wiring

Components used to make the Single phase timer & contactor wiring:

01. DP MCB

Fig 2: DP MCB

Double pole MCB can control two wires. This circuit breaker is generally used in single-phase electric lines. Double pole MCB circuit breaker input has two wires supply two wires and an output. In a single-phase line, A double-pole MCB circuit breaker is used to give good production. This circuit breaker is provided through phase and neutral circuit breaker, it is very safe. This circuit breaker is preferred for home appliances. A DP MCB usually trips for 2 reasons 1. Overload 2. Short circuit.

02. Contactor

Fig 3: Contactor

A magnetic contactor is an electrical device used for load control, automation, and protection. It is much like a magnetic reel. However, relays are generally used for low power and voltage, on the other hand, when we think of high power, these heavy-duty contractors only come to mind. It basically works by switching the load on and off. It has 3 terminals whose inputs are denoted as L1, L2, L3, and outputs as T1, T2, and T3. The circuit of the load is made in automation mode or protection using auxiliary contacts. It has two types of terminals. 1) Normally Open (NO). 2) Normally Closed (NC)

03. Timer

Fig 4: Timer

Timer is a specialized type of clock used for measuring specific time intervals.An electromechanical cam timer uses a small synchronous AC motor turning a cam against a comb of switch contacts. This type of timer often has a friction clutch between the gear train and the cam, the cam can be turned to reset the time.A simple example of the first type is an hourglass. Working method timers have two main groups: hardware and software timers.Most timers give an indication that the time interval that had been set has expired.

04. Start Switch

Fig 5: Start Switch

The operator switch has its contact in Normally Open condition. To make Ladder Logic you need to understand NO contact. A Classic Switch has one Input And one Output. In "No Switch," YoungBoy Raps About Ammunition, Murder, Firearms, and Firearm Attachments Such as a Switch. The contact of the switch whose contact is already open is NO. That is enough to understand. no switch in a circuit, then the circuit will not function as intended. to write a program such that when the red light is on, This switch is now in normally open condition. When you push the switch it will close and the red light will turn on.

05. Stop Switch

Fig 6: Stop Switch

Indicates the contacts of switches or automatic actionable devices. Simply put, the push switches, magnetic contactors, and relays that we use in the factory Normally have Close Contact exists. At this moment the switch will be in normally closed condition. Because already he is sitting close. When turned off the contact will open. To make ladder logic you need to understand NC contact. As already explained. The switch contact is already closed in NC. That is enough to understand.

06. Indicator Light

Fig 7: Indicator Light

An electric current Flow Indicator Senses The electrical Current Through an electrical device And produces visible feedback to Indicate Proper Operation. The Current Flow Indicator Has Voltage And Current Regulation Craving First And Second Inputs Connected To The First And Second Conductors, Respectively. This Publication Provides updated Statistics on a Comprehensive Set of social, Economic, Financial, and Environmental Measures as Well as Select Indicators for Sustainable Development Goals.

Thank You for visiting the website. Keep visiting for more Updates.