Motion Sensor with 2-way switch wiring

Motion Sensor with 2-way switch wiringTitle:

This diagram shows how to make Motion Sensor with two-way switch wiring. In this circuit, we use, a motion sensor, a light, a DP MCB ( Double Pole Miniature Circuit Breaker ), and a 2-way switch. Here connect all components with power. This circuit is ready for use. If you want to know more about this circuit please stay with check our youtube video below the post.

Diagram of motion sensor wiring:

Fig 1: Motion Sensor with 2-way switch wiring

Components Need for this Project:

You can get the components from any of the sites below:

1. Motion Sensor [See Buy Click Amazon]
2. Light [See Buy Click Amazon]
3. DP MCB [See Buy Click Amazon]
4. 2-way Switch [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

$ads={1}

Read Also:

• Day Night Sensor using Contactor wiring | Day night sensor wiring

• Automatic Water Level Controller Wiring

• Single phase ampere meter connection | Amp meter Installation

• Install Voltmeter wiring diagram | Voltmeter wiring diagram

• Light Switch Wiring Diagram | Two way light switch wiring diagram

Components used to make the motion sensor wiring:

01. Motion Sensor

Fig 2: Motion Sensor

An Automatic Day Night Light Sensor Switch can Switch on Any Electrical Device Automatically When Dark Falls And Switch off in the Morning Automatically. This Night light With an Energy-Efficient LED (Light Emitting Diode) can be Plugged into the Socket and has a light sensor so that the lamp switches on automatically when it gets dark. This is a Photo Technology-Based automatic sensor switch for 220V AC mains, which can be Widely Used in Street Lights, Factories, Gardens, Shops, Etc., and Other Places for Automatic Lighting. Turns ON the Light in the Dark & Turns OFF in The Light.

02. Light

Fig 3: Light

CFLs work in a completely different way from ordinary lamps, they work by using a different process called fluorescence rather than generating light from heat. A typical light bulb wastes 90% of energy and converts only 10% of energy into light, this is where CFL has the biggest advantage. CFL- Curved or conical glass tube filled with argon and a small amount of mercury vapor. The inner wall of the glass is coated with fluorescent material. CFL- It is manufactured using the principle of creating fluorescent light. CFL- Originally white in color but now the construction and use of CFLs producing colored light has become popular.

03. DP MCB

Fig 4: DP MCB

Double pole MCB can control two wires. This circuit breaker is generally used in single-phase electric lines. Double pole MCB circuit breaker input has two wires supply two wires and an output. In a single-phase line, A double-pole MCB circuit breaker is used to give good production. This circuit breaker is provided through phase and neutral circuit breaker, it is very safe. This circuit breaker is preferred for home appliances. A DP MCB usually trips for 2 reasons 1. Overload 2. Short circuit.

04. 2-way Switch

Fig 5: 2-way Switch

The two-way switch is a type of multiway switch. Multiway switches have more points and can be controlled in multiple ways simultaneously. The middle connection normally goes to the load and the two side connections act as switches. Again, the opposite is also true if it is used in the lamp connection.It is a type of switch that has three wire connections. And it really has no off or on. Both sides can be turned on or off depending on how you connect one to the other. The two-way switch is a type of multiway switch. Multiway switches have more points and can be controlled in multiple ways simultaneously. Two Way Switch has three wire connection system.

Thank You for visiting the website. Keep visiting for more Updates.

$ads={2}

Frequently Asked Questions

How is a 2-way switch wiring?

Another way is to run a Live wire to both L1s and a Neutral wire Circuit diagram to both L2s, then run a single wire between the 2 Common Power Supply terminals. The lamp should be on the Neutral wire Circuit Diagram, between the consumer unit and where the wire splits to meet the Project System switches.

How do you wire a motion sensor to multiple lights?

Daisy Chain: One way to connect multiple lights to a single motion sensor is by using a daisy chain method. This involves connecting the motion sensor to the first light, then connecting a cable from the first light to the second light, and so on.

What is 1 way vs 2 way switch wiring?

1-Way Switches: If a light switch is '1 way' this means it is just an on/off switch Circuit diagram. This is the simplest type of and-on switch that you can get. The single switch controls a single light (or lighting circuit diagrams). 2-Way Switches: A '2-way' switch means there is another switch controlling the same light.

How does a 2 wire sensor work?

Unlike a mechanical switch, a 2-wire sensor as an active component Power supply requires voltage and current at all times. This means that even when closed, a non-negligible Circuit diagram voltage, missing from the connected load, drops across the sensor. When open, a current flows through the sensor and the connected load project system.

Can motion sensors be wired in parallel?

Where lighting is required, a motion-activated switch for such lighting must also have a manual on/off switch. This requirement is usually implemented as an on/off/auto switch Circuit diagram. So two motion-activated switches in parallel are fine, as long as both have the power supply manual override (which all generally do).