Tube light connection with one choke | led tube light connection

Tube light connection with one choke:

This Diagram Shows An Electrical Choke is Connected in Series with the Tube Light. The Choke has an Inductor Coil Inside it Which Creates a High Voltage During the Starting Time of The Tube Light. Tube Light is a Lamp That Works on Low-Pressure Mercury Vapor Discharge Phenomenon and Converts Ultra Violate Rays Into Visible Rays With The Help of Phosphor Coated Inside a Glass Tube.

Diagram of Tube light connection with one choke wiring:

Fig 1: Tube light connection with one choke

Components Need for this Project:

You can get the components from any of the sites below:

1. Tube Light [See Buy Click Amazon]
2. Ballast Coke [See Buy Click Amazon]
3. Switch [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

$ads={1}

Read Also:

• Single Phase Motor Reverse Forward Switching

• Single Phase Motor Starter With Timer Diagram

• Single Phase split AC indoor-outdoor wiring

• Split ac indoor Outdoor wiring air conditioner

• Single-Phase Submersible Pump Motor Wiring

Components used to make the Tube light connection with one choke:

01. Tube Light

Fig 2: Tube Light

A fluorescent lamp, tube light, or rod light is a type of electric lamp that uses electricity to excite mercury vapor to produce light. These lamps are mainly used as an artificial source of light. When the mercury vapor inside a fluorescent lamp is excited with electricity, the mercury molecules emit short-wavelength ultraviolet light that hits fluorescent particles to produce visible light. Fluorescent lamps always require a ballast to control the flow of electrical energy inside the lamp, which is required by incandescent lamps. is not

02. Ballast Coke

Fig 3: Ballast Coke

The word Ballast means balancer. Some of the problems mentioned above are in lighting the tube light in the preheating method. Basically electronic ballast is prepared to eliminate this problem. As a result, the tube light switches on and lights up the house. The type of ballast through which this is done is called electronic ballast. Basically, the tube light system also ballast play the role of the balancer. It stabilizes the current and voltage. If a tube light is connected directly to the main line without this ballast, excessive current will flow through the tube light.

03. Switch

Fig 4: Switch

A Single-Pole, Single-Throw (SPST) Switch. It's Got one Output and One Input. The Switch will Either be Closed or Completely Disconnected. SPSTs are Perfect for on-off Switching. They're also a Very Common Form of Momentary Switches. SPST Switches are Commonly Used in a Variety of Electrical Circuits and Applications, Such as Turning on And off Lights, Fans, and Other Appliances. They can Also be Used to Control the Flow of Electricity to Different Parts of a Circuit or to Switch Between Different Circuits Altogether.

Thank You for visiting the website. Keep visiting for more Updates

$ads={2}

Frequently Asked Questions

What is the difference between coil and choke?

An inductor coil is used to store and release energy in a circuit, often to smooth out current or voltage fluctuations. A choke coil, on the Currenttlou other hand, is specifically designed to block high-frequency power supply alternating current (AC) while allowing direct Circuit diagram current (DC) or low-frequency AC to pass through.

What is an inductor or choke-in tube light?

The inductor choke helps regulate the power supply current and voltage in the circuit diagram, which is necessary for the proper operation of the project system tube light. It also helps to stabilize the current electrical flow, preventing damage to the power supply tube and ensuring a steady and consistent project system light output.

What is the output voltage of a tube light choke?

Usually, the output of a choke while running is only 110 volts to limit the current and to run the current smoothly. But the output of a choke while starting is more than 1000 volts. This high voltage is required to strike an arc. So the voltage on starting is more than 1000 volts.

What are the applications of choke?

Choke coils have various applications in various electronic power supply devices and equipment. They are critical in regulating electrical currents and protecting devices from damage. From power supply supplies to audio equipment and lighting fixtures, choke coils are essential to many Circuit diagram electronics.

How does a choke coil produce high voltage?

As the tube heats up, the choke coil allows more power supply current to flow, which in turn increases the voltage across the Circuit diagram tube. This process helps the tube light to produce high voltage and maintain a stable operating condition.