Contactor wiring With Latching Circuit | 3 phase contactor wiring with timer

Contactor wiring With Latching Circuit:

This diagram shows how to connect the Contactor wiring With Latching Circuit with timer Latching relay wiring. In this circuit diagram, we just try to describe simply how to connect the Contactor wiring With Latching Circuit with a timer Latching relay to house loads like. This diagram is for Contactor wiring With Latching Circuit with a timer Latching relay. So you can wire your house or office like this diagram very easily. If you want to learn how to connect this circuit clearly you can follow our youtube video link below.

Diagram of Contactor wiring With Latching Circuit:

Fig 1: Contactor wiring With Latching Circuit

Components Need for this Project:

You can get the components from any of the sites below:

TP MCB [See Buy Click Amazon]
8-Pin Timer [See Buy Click Amazon]
Magnetic Contactor [See Buy Click Amazon]
3-Phase Motor [See Buy Click Amazon]
Emergency Switch [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the Contactor With Latching Circuit:

01. TP MCB

Fig 2: TP MCB

Three wires can be controlled by a triple pole MCB. Triple pole MCB circuit breakers are generally used in three-phase lines. A triple-pole MCB circuit breaker has three wires at its input and three wires at its output. But one can use this circuit breaker in a single-phase line. TP MCB widely used in industries. The reason is that it has three poles. And this TP circuit breaker is used to provide three-phase and three-phase connections. A neutral is not normally used in three-phase lines. But a 4-pole MCB circuit breaker is used if needed.

02. 8-Pin Timer

Fig 3: 8-Pin Timer

Timer is a specialized type of clock used for measuring specific time intervals.An electromechanical cam timer uses a small synchronous AC motor turning a cam against a comb of switch contacts. This type of timer often has a friction clutch between the gear train and the cam, the cam can be turned to reset the time.A simple example of the first type is an hourglass. Working method timers have two main groups: hardware and software timers.Most timers give an indication that the time interval that had been set has expired.

03. Magnetic Contactor

Fig 4: Magnetic Contactor

A magnetic contactor is an electrical device used for load control, automation, and protection. It is much like a magnetic reel. However, relays are generally used for low power and voltage, on the other hand, when we think of high power, these heavy-duty contractors only come to mind. It basically works by switching the load on and off. It has 3 terminals whose inputs are denoted as L1, L2, L3, and outputs as T1, T2, and T3. The circuit of the load is made in automation mode or protection using auxiliary contacts. It has two types of terminals. 1) Normally Open (NO). 2) Normally Closed (NC).

04. 3-Phase Motor

Fig 5: 3-Phase Motor

A Three-Phase Motor is an Electric Motor That Typically Receives its Power From a Three-Phase System (three-phase current) This can be realized via a Three-Phase Mains Supply or a Frequency Inverter. Three-Phase Motors are Available as Synchronous and Asynchronous Motors. Three Phase Alternating Current Power Motor is Economical to Supply Power to the data Center Since it Requires Less Conductor Material to Supply Electricity. This Explains Why 3 Phase Alternating Current Motor is Used in Electric Transmission, Generation, and Distribution in Most Countries Worldwide.

05. Emergency Switch

Fig 6: Emergency Switch

An Emergency Stop Switch is a Safety Mechanism Used to Shut off Machinery in an Emergency When it Cannot be Shut Down in The Usual Manner. The Purpose of an Emergency Push Button is to Stop The Machinery Quickly When There is a Risk of injury or The Workflow Requires Stopping. Machinery And Equipment Used in Factories and Other Facilities are Equipped With an Emergency Stop Function to Stop The Machinery And Equipment in an Emergency to Ensuring Operator Safety as Complementary protective measures.

Thank You for visiting the website. Keep visiting for more Updates.

Contactor wiring With Latching Circuit | 3 phase contactor wiring with timer