Automatically Simple 3-Phase Motor Control | 3-phase motor control circuit

Automatically Simple 3 Phase Motor Control:

This diagram shows how to connect automatically Simple 3 Phase Motor Control wiring. In this circuit diagram, we just try to describe simply how to connect an Automatically Simple 3 Phase Motor Control to house loads like. This diagram is for Automatically Simple 3 Phase Motor Control wiring. So you can wire your house or office like this diagram very easily. If you want to learn how to connect this circuit clearly you can follow our youtube video link in below.

Diagram of Automatically Simple 3 Phase Motor Control:

Fig 1: Automatically Simple 3 Phase Motor Control

Components Need for this Project:

You can get the components from any of the sites below:

1. 3-Phase Motor [See Buy Click Amazon]
2. Ampere Meter [See Buy Click Amazon]
3. Magnetic Contactor [See Buy Click Amazon]
4. Start Switch [See Buy Click Amazon]
5. Stop Switch [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

• 3 Phase Motor Control With Monopolar switch

• Delta to Delta Transformer connection

• Delta to Star Transformer connection

• 3-phase Induction Motor wiring connection

• 2-Way Switch Control in 3-Phase Motor

Components used to make the 3 Phase Motor Control:

01. 3-Phase Motor

Fig 2: 3-Phase Motor

A Three-Phase Motor is an Electric Motor That Typically Receives its Power From a Three-Phase System (three-phase current) This can be realized via a Three-Phase Mains Supply or a Frequency Inverter. Three-Phase Motors are Available as Synchronous and Asynchronous Motors. Three Phase Alternating Current Power Motor is Economical to Supply Power to the data Center Since it Requires Less Conductor Material to Supply Electricity. This Explains Why 3 Phase Alternating Current Motor is Used in Electric Transmission, Generation, and Distribution in Most Countries Worldwide.

02. Ampere Meter

Fig 3: Ampere Meter

The Ammeter (Abbreviation of Ampere Meter) is a Measuring Instrument used to find the Strength of the Current Flowing Around an Electrical Circuit when Connected in Series with the part of the Circuit Being Measured. For Direct Measurement, The Ammeter is Connected in Series With the Circuit in Which The Current is to be Measured. An Ammeter’s Current Sensitivity is Determined by the Amount of Electric Current Required by the coil of the Meter to Produce the Required FSD Movement of the Pointer.

03. Magnetic Contactor

Fig 4: Magnetic Contactor

A magnetic contactor is an electrical device used for load control, automation, and protection. It is much like a magnetic reel. However, relays are generally used for low power and voltage, on the other hand, when we think of high power, these heavy-duty contractors only come to mind. It basically works by switching the load on and off. It has 3 terminals whose inputs are denoted as L1, L2, L3, and outputs as T1, T2, and T3. The circuit of the load is made in automation mode or protection using auxiliary contacts. It has two types of terminals. 1) Normally Open (NO). 2) Normally Closed (NC).

04. Start Switch

Fig 5:Start Switch

The operator switch has its contact in Normally Open condition. To make Ladder Logic you need to understand NO contact. A Classic Switch has one Input And one Output. In "No Switch," YoungBoy Raps About Ammunition, Murder, Firearms, and Firearm Attachments Such as a Switch. The contact of the switch whose contact is already open is NO. That is enough to understand. no switch in a circuit, then the circuit will not function as intended. to write a program such that when the red light is on, This switch is now in normally open condition. When you push the switch it will close and the red light will turn on.

05. Stop Switch

Fig 6: Stop Switch

Indicates the contacts of switches or automatic actionable devices. Simply put, the push switches, magnetic contactors, and relays that we use in the factory Normally have Close Contact exists. At this moment the switch will be in normally closed condition. Because already he is sitting close. When turned off the contact will open. To make ladder logic you need to understand NC contact. As already explained. The switch contact is already closed in NC. That is enough to understand.

Thank You for visiting the website. Keep visiting for more Updates.