2 Motor automatic control with Timer

2 Motor Automatic Contol with Timer

This Diagram shows 2 motor automatic control with timer. This process starts with the starting Switch formerly pressed, also the motor will turn ON and OFF automatically with a timer. There's a Stop Switch to stop the process at any time or in an exigency situation. Once the Stop switch is pressed, the process will start by pressing the starting Switch There are also connected magnetic contactors and double pole MCB.

Two Motor Contol With Timer Wiring Diagram

Fig 1: 2 Motor contol with timer

Components Need for this Project:

You can get the components from any of the sites below:

Magnetic Contactor [See Buy Click Amazon]
DP MCB [See Buy Click Amazon]
8 Pin Timer [See Buy Click Amazon]
Single phase Motor [See Buy Click Amazon]
Indicator Light [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

~~$ads={1}~~

Read Also:

Components used to make the 2 Motor Control by Timer:

01. Magnetic Contactor

Fig 2: Magnetic Contactor

A magnetic contactor is an electrical device used for load control, automation, and protection. It is much like a magnetic reel. However, relays are generally used for low power and voltage, on the other hand, when we think of high power, these heavy-duty contractors only come to mind. It basically works by switching the load on and off. It has 3 terminals whose inputs are denoted as L1, L2, L3, and outputs as T1, T2, and T3. The circuit of the load is made in automation mode or protection using auxiliary contacts. It has two types of terminals. 1) Normally Open (NO). 2) Normally Closed (NC)

02. DP MCB

Fig 3: DP MCB

Double pole MCB can control two wires. This circuit breaker is generally used in single-phase electric lines. Double pole MCB circuit breaker input has two wires supply two wires and an output. In a single-phase line, A double-pole MCB circuit breaker is used to give good production. This circuit breaker is provided through phase and neutral circuit breaker, it is very safe. This circuit breaker is preferred for home appliances. A DP MCB usually trips for 2 reasons 1. Overload 2. Short circuit.

03. 8 Pin Timer

Fig 4: 8-pin Timer

Timer is a specialized type of clock used for measuring specific time intervals.An electromechanical cam timer uses a small synchronous AC motor turning a cam against a comb of switch contacts. This type of timer often has a friction clutch between the gear train and the cam, the cam can be turned to reset the time.A simple example of the first type is an hourglass. Working method timers have two main groups: hardware and software timers.Most timers give an indication that the time interval that had been set has expired.

04. Single phase Motor

Fig 5: Single phase Motor

Single-Phase Induction Motor is Very Simple in Construction, Economical, Reliable, and Easy to Repair And Maintain. Due to all these advantages, it is widely used in vacuum cleaners, fans, centrifugal pumps, blowers, washing machines, etc. It can run only by supplying 1 phase current through this motor. The main two parts of this motor are Rotor and Stator. Among them, the rotating part is the Rotor and the stationary part is the Stator. Like all induction motors, a single-phase induction motor consists of two main parts, the stator, and the rotor.

05. Indicator Light

Fig 6: Indicator Light

LED (light emitting diode) is basically a type of diode that emits light at a certain voltage. These LED bulbs turn on at a very low voltage such as 2~3 volts. When the light emitting diode is forward biased, the free electrons in the n-type semiconductor gain electrical energy from the DC source and move from the balance band to the conduction band and the electrical Under the influence of pressure, current flows through the junction to P-type. In the p-type majority of carrier holes are located in the valence band. Thus basically the p-n junction becomes a light source.

Thank You for visiting the website. Keep visiting for more Updates.

~~$ads={2}~~

Frequently Asked Questions

What is the use of a timer in motor control?

Timers could also be used to provide both plugging and anti-plugging for certain circuit diagrams. Indeed the range of applications for timers is nearly limitless. A device that controls the flow of electrical power supply to a motor. It is designed to safely start and stop the motor, and provide overload protection.

What is automatic motor control?

The motor control switches and devices can regulate the operation of electrical motors. They could provide manual or automatic functions, start and stop the motor, control forward or reverse motions, speed up or slow down, and more.

What are the 3 types of automatic control?

The methods used to accomplish the control objectives can be classified, very generally, as open-loop controls and closed-loop or feedback 3 controls. Systems in which the output quantity does not affect the input quantity are called open-loop control systems. Open-loop controls are, in general, calibrated systems 3.

What are the two types of automatic control?

The methods used to accomplish the control objectives can be classified, very generally, as open-loop controls and closed-loop or feedback controls. Systems in which the output quantity does not affect the input quantity are called open-loop control systems. Open or loop controls are, in general, calibrated in the systems.

Why is motor control important?

The simplest definition is how the nervous system – motor, sensory, and central processes – controls posture and movement to perform motor tasks. Motor control exercises then aim to change the way a person controls their body, often concerning the loading of the spine and adjacent structure.